- Browse all categories
- Best Picks by Swift Karting: The Essential Pit Tools
-
- Brake Bleeder Kit
- Brake Fittings & Ferrules
- Brake Fluid
-
Brake Hubs
- Brake Line
-
Brake Parts (M.C.P.)
-
Brake Rotors
- Caliper Brackets
- Enginetics Parts
- Euro Brake Pads
- Front Wheel Brakes
- Master Cylinder Caps, Billet
- Quarter Midget Brakes
- Rotor Guards
-
- Alfano Gauges & Accessories
- Hour Meter
-
Mychron Gauges
- Stopwatches
- Tach Bags
- Transponder Holders
-
-
Axle Bearings
- Axle Cassettes
-
Axles & Accessories
-
Bully Clutches
-
Chain
- Chain Breaker Tools
- Clutch Drivers
- Clutch Friction Discs
- Clutch Mounting Bolt Kits
- Clutch Spacers
-
Hilliard Clutches
- Honda GXH50 Kid Kart Clutch
-
Horstman Clutch Parts
- Lock Collars
-
Max-Torque Clutches
-
Nor-Am Clutches
-
Premier Clutches
- SMC Kart Clutches
- Sprocket Guards & Hardware
-
Sprocket Hubs
-
Sprockets
-
Viper Clutches
-
-
-
196cc Clone Engine & Parts
-
212cc Clone / Predator Engine & Parts
- 224cc Clone Engine & Parts
- Air Filters & Pre Filters (1.25")
-
Air Filters & Pre Filters (2-7/16")
- Big Block Clone Accessories
-
Briggs LO206 Engines & Parts (LO206)
- Briggs Quarter Midget Engine and Parts
- Briggs World Formula
- Camshafts
- Carb Cover (2-7/8")
- Carb Manifolds
- Catch Tanks
- Chain Guards & Hardware
- Exhaust Header Wrap
- Exhaust Silencers & Clamps
- Flywheel Screens
- Fuel Filters
- Fuel Line
- Fuel Pumps
-
Fuel Tanks
-
Gaskets (Fel-Pro)
- Honda GXH50 Kid Kart
-
Motor Mounts
-
Oil & Additives
- Pulse Fittings
-
Raptor (Flathead) Parts
- Spark Plug Index Washers
- Spark Plugs (2-Cycle & Honda Kid Kart)
- Throttle Cables & Hardware
- Tillotson Carbs
- Wiseco Pistons
-
- Track Wear, Kart Life Apparel
Dyno Cams
Extra Fine Thread Rocker Jam Nut (Each) for Secure Clone Adjustments
Extra Fine Thread Rocker Jam Nut (Each) for Secure Clone Adjustments
Couldn't load pickup availability
Secure your rocker adjustments with the CL-1090 extra fine jam nut, designed for precise locking in clone engines.
- Fine Threads: Enable exact lash tuning without slippage.
- Matches JF168-1270EFKIT specs for compatibility.
- Sold individually for on-demand fixes.
Keeps valvetrain tight, boosting reliability. SKU: CL-1090.
Frequently Asked Questions
Q: Why should I use an extra fine thread jam nut for my rocker arm?
A: Extra fine threads allow for much more precise lash adjustments compared to standard coarse threads. This precision is critical in high-performance clone engines to ensure your valve lash stays exactly where you set it, preventing slippage during high-RPM racing.
Q: Is this jam nut compatible with stock clone rocker arms?
A: Yes, the CL-1090 is designed to match the specifications of the JF168-1270EFKIT and is a direct replacement for standard clone valvetrain setups requiring fine-thread hardware.
Q: How tight should I torque the jam nut?
A: You should tighten the jam nut firmly against the rocker arm adjuster to lock it in place. Be careful not to overtighten, as this can strip the threads or damage the adjuster stud. Always double-check your lash clearance after locking the nut to ensure the setting didn't shift during tightening.
Q: Should I replace my jam nuts during a valve train rebuild?
A: It is highly recommended. Over time, the threads on jam nuts can wear or stretch, which may lead to the nut backing off under engine vibration. Replacing them ensures your valvetrain remains secure and reliable throughout the race season.
Related Products From Vendor
- Dyno Cams CL-1076 Stamped Y Square Tip Rocker Arm - Low-Lift - 196cc Clone
- 1:1 Ratio Square Tip Clone Rocker Arm LQ (Each) for Consistent Lift
- Dyno Cams CL-1075-LQ Low-Lift Clone Rocker Arm - Round Tip - 196cc/GX200
- Standard 134mm Stainless Steel Clone Push Rod for Reliable Lift
- Dyno Cams 196cc Clone 133mm Stainless Steel Push Rod - 11.15g - Unrestricted Class
Share
